Developer notes:

Before auto-discovery is implemented, you can follow the steps below to activate a Maple PON. These steps assume:

• Voltha starts with fresh state (was just launched in single-instance mode)
• Maple OLT and Broadcom ONU(s) are powered on and properly connected with splitters.
• There is network reach from Voltha's host environment to the Broadcom Maple OLT via a specific interface of the host OS. We symbolically refer to this Linux interface as <interface>.
• All commands are to be executed from the root dir of the voltha project after env.sh was sourced, and at least 'make protos' was executed on the latest code.

Step 0: Bring up the supporting docker containers

cd ~/voltha
. env.sh
docker-compose -f compose/docker-compose-system-test.yml up -d \
    consul zookeeper kafka fluentd registrator shovel grafana

Step 1: Launch Voltha (in its terminal window)

cd ~/voltha
. env.sh
./voltha/main.py --kafka=@kafka

Step 2: Launch Chameleon (in a different terminal)

cd ~/voltha
. env.sh
./chamaleon/main.py  -f pki/voltha.crt -k pki/voltha.key

Step 3: Verify Maple and Broadcom adapters loaded

In a third terminal, issue the following REST requests:

curl -k -s https://localhost:8881/api/v1/local/adapters | jq

This should list (among other entries) two entries for Broadcom devices: one for the Maple OLT and one for the Broadcom ONU.

The following request should show the device types supported:

curl -k -s https://localhost:8881/api/v1/local/device_types | jq

This should include two entries for Broadcom devices, one for the OLT and one for the ONU.

Step 4: Pre-provision a Maple OLT

Issue the following command to pre-provision the Maple OLT:

curl -k -s -X POST -d '{"type": "maple_olt", "ipv4_address": "111.111.111.111"}' \
    https://localhost:8881/api/v1/local/devices | jq '.' | tee olt.json

This shall return with a complete Device JSON object, including a 12-character id of the new device and a preprovisioned state as admin state (it also saved the json blob in a olt.json file):

{
  "vendor": "",
  "software_version": "",
  "parent_port_no": 0,
  "connect_status": "UNKNOWN",
  "root": false,
  "adapter": "tibit_olt",
  "vlan": 0,
  "hardware_version": "",
  "ports": [],
  "parent_id": "",
  "oper_status": "UNKNOWN",
  "admin_state": "PREPROVISIONED",
  "mac_address": "00:00:00:00:00:01",
  "serial_number": "",
  "model": "",
  "type": "maple_olt",
  "id": "2db8e16804ec",
  "firmware_version": ""
}

For simplicity, store the device id as shell variable:

OLT_ID=$(jq .id olt.json | sed 's/"//g')

Step 5: Activate the OLT

To activate the OLT, issue the following using the OLT_ID memorized above:

curl -k -s -X POST https://localhost:8881/api/v1/local/devices/$OLT_ID/activate

After this, if you retrieve the state of the OLT device, it should be enabled and in the 'ACTIVATING' operational status:

curl -k -s https://localhost:8881/api/v1/local/devices/$OLT_ID | jq '.oper_status,.admin_state'
"ACTIVATING"
"ENABLED"

When the device is ACTIVE, the logical devices and logical ports should be created. To check the logical devices and logical ports, use the following commands.

curl -k -s https://localhost:8881/api/v1/local/logical_devices | jq '.'
# Note: Need to pull out logical device id.
curl -k -s https://localhost:8881/api/v1/local/logical_devices/47d2bb42a2c6/ports | jq '.'

OLD stuff

[This will be moved to some other place soon.]

To get the EOAM stack to work with the ONOS olt-test, the following command was used in the shell to launch the olt-test.

NOTE: This command should soon be eliminated as the adapter should be started by VOLTHA. By running the commands as listed below, then the olt-test can take advantage of the virtual environment.

$ cd <LOCATION_OF_VOLTHA>
$ sudo -s
# . ./env.sh
(venv-linux) # PYTHONPATH=$HOME/dev/voltha/voltha/adapters/tibit ./oftest/oft --test-dir=olt-oftest/ -i 1@enp1s0f0 -i 2@enp1s0f1 --port 6653 -V 1.3 -t "olt_port=1;onu_port=2;in_out_port=1;device_type='tibit'" olt-complex.TestScenario1SingleOnu